Rohde & Schwarz RT-ZP05 - Passive Probe, 500 MHz

Key Facts

 

• Attenuation factor: 10:1
• Bandwidth: 500 MHz
• Dynamic range: 300 V (RMS)
• Input impedance: 10 MΩ || 10 pF
• Extensive accessories for optimal contacting

Rohde & Schwarz passive probes are the all-rounders in the world of probes. They are low-cost, general purpose solutions for a broad range of applications.

Universal application

Rohde & Schwarz passive probes are the all-rounders in the world of probes. They are low-cost, general purpose probing solutions for a broad range of applications. The BNC connector allows them to be used on almost any oscilloscope. Passive probes with readout pin enable Rohde & Schwarz oscilloscopes to automatically detect the attenuation factor. A spring-loaded tip ensures good contact with the DUT.
 

Individual adjustment for precise measurements

In order to achieve optimum measurement accuracy, passive probes with a probe bandwidth larger than 350 MHz must be adjusted to the input impedance of the oscilloscope. Rohde & Schwarz offers the R&S RTM-ZP10 and the R&S RT-ZP10 500 MHz passive probes, which are preadjusted for the R&S RTM and the R&S RTO oscilloscopes, respectively.
 

Extensive accessories

For optimal contacting, Rohde & Schwarz offers the R&S RT-ZA1 accessory set for passive probes. It includes spare spring-loaded tips, rigid tips, ground contact springs, ground leads and color-coded rings.
 

Derating - Derating curve

Adjustment

The probe can be adjusted for low frequency compensation (LF). Connect the probe to a 1 kHz square wave signal. Adjust LF compensation trimmer (LF Comp.) for optimum square wave response.

1 kHz Signal (LF)

Product Name	Bandwidth	Maximum Voltage	Attenuation Factor	Input Impedence	Comment
RT-ZP1X	38 MHz	55 V (RMS) (CAT II)	1:1	1 MΩ || 39 pF
RT-ZP03	300 MHz	400 V (RMS) 55 V (RMS)	10:1 1:1	10 MΩ || 12 pF 1 MΩ || 82 pF
RT-ZP05S	500 MHz	300 V (RMS)	10:1	10 MΩ || 10 pF	Dual pack available: R&S RT-ZP05
RTM-ZP10	500 MHz	400 V (RMS) 300 V (RMS) (CAT II)	10:1	10 MΩ || 9.5 pF	2.5 mm tip diameter, pre-adjusted for R&S RTM2000
RT-ZP10	500 MHz	400 V (RMS) 300 V (RMS) (CAT II)	10:1	10 MΩ || 9.5 pF	2.5 mm tip diameter, pre-adjusted for R&S RTO2000/R&S RTE1000
RT-ZI10	500 MHz	600 V (RMS) (CAT IV) 1000 V (RMS) (CAT III)	10:1	10 MΩ || 12 pF	Dual and quad packs available for R&S RTH handheld oscilloscope: R&S RT-ZI10C-2, R&S RT-ZI10C-4
RT-ZI10C	500 MHz	300 V (RMS) (CAT III)	10:1	10 MΩ || 11 pF	For R&S RTH handheld oscilloscope
RT-ZI11	500 MHz	600 V (RMS) (CAT IV) 1000 V (RMS) CAT III 3540 V (pk) (CAT 0)	100:1	100 MΩ || 4.6 pF	For R&S RTH handheld oscilloscope